Anyone got any other ideas? This easy to follow silent and accurate video will guide you quickly and easily through what you'll need, like a Power Supply, a sound system that has a Subwoofer Pre-output and a High Input adapter, which may already come with your amp. Refer to instructions for your specific sub or preamplifier for questions on available adjustments. A Neutrik Speakon lead in parallel to the speaker terminals on the amp to the Neutrik Speakon socket on the subwoofer. I just purchased and installed a kicker dxa125. Now, connect your amplifiers to their power source, check your wiring; then turn it on.
This will come into play later. There are a few ways that one can expect to connect a subwoofer to an amplifier, receiver, or processor also known as a home theater receiver. Then connect 4 4ohm speakers in series to make 12ohm on the left side of the amp. Secure all wiring using cable ties. That 5th channel has a sub positive and sub negative input. In parallel the total impedance is half of the impedance of the speakers, so that your two 3 ohm speakers would give a total load impedance of 1. If this page has helped you, or perhaps even saved you paying for a technician, please consider a donation to Geoff to encourage him and appease his wife for the many hours he puts into this website.
Otherwise, set the receiver to output the rear, use two patch cord pairs for the 4 channel inputs, and either get the sub channel signal via Y-cord from the rear channels or the amp has an onboard feature that gets the sub's signal internally. Eight of the wires coming from the receiver harness are the speaker outputs of the receiver and, using this wiring system, you no longer need them so they can be cut or taped so they won't make any contact with metal. This needs to be done to avoid having the amp stay switched on when you turn your ignition off, draining your car's battery flat. That could drive the Sub to high levels depending upon the input sensitivity in the Sub's amp if it's a powered Sub. Switch off the system completely before playing with cables. But if you want to add a sub later, you'd want to get a 6-channel processor.
To do that is it something as simple as just unplugging the wire from the old speakers and plugging them into the new ones? They are labeled Left and Right line-in inputs, but for a typical home theater, you only have one cable coming from the receiver to the subwoofer. If I were to want to power the 6x9s in back and the 4x6s in front, how would I go about wiring a separate 4 channel amp. In other words, can I run a speaker wire from my right speaker to one subwoofer and then run another speaker wire from my left speaker to the other subwoofer? Â Hi Todd, You seem to have sorted it out. Check out our for details. There are also 2 ways to hook them up, not all having the ability to do both.
Plugging in and Hooking up Your Subwoofer If you have a subwoofer cable and a Y-adapter, this is the optimal setup for your sub. This way you can get 2 for less than the price of 1 subwoofer! Both the theory and practical points on how to connect 2 speakers are discussed. If you cut a wire, it should get capped off with a crimp or heat shrink so no short circuits can occur. For more information read this post on. Because the subwoofer is working mostly on the bass the low tones , it doesn't require as much directional pushing as speakers do. My question is do I need to run new thicker gauge speaker wire or will I be fine with the factory wires? Enjoy your Subwoofer and all the Bass it has to Offer That's all there is to it for connecting your powered subwoofer.
. This is because two 8 ohm speakers in parallel makes the total load impedance 4 ohms. The remote wire tells the amp to turn on. This article has also been viewed 966,308 times. Using the subwoofer's onboard crossover to feed your speakers may not be the best idea for a purely music system. Could you hook up the sub to the tape out? The connection to the amp is easy.
Whether in your car or your home theatre, a subwoofer is a must for a true and complete audio experience. So you can be used without stressing out is not have paint on how to hook up the sub, if you're hooking up your sub. Now I want to upgrade my two rear speakers to the infinity kappa 693. I think this is pretty typical of subwoofer connection options. For me go over what you need an easy aftermarket. Then connect 2 volume controls with one speaker each to the right side of the amp. Connect the amp's main power wire to the positive battery lead and reconnect the positive battery lead to the positive battery terminal.
My main comment is on your math. Set the phase control on the amplifier to zero and the output to minimum. If you buy your wires from Crutchfield, you could call Tech Support for free help wiring your system. You guys are a great information source. My only suggestion to achieve what you are wanting, is to use a two zone speaker selector switch with volume controls. My question is how many channels would I need on the processor as well as the amp? Each speaker may have a different sensitivity which may mean there will be a level difference between them. The sub's on-board crossover is then adjusted to match the lowest frequency handled by your main speakers so as to take over and extend the range reproduced.
Therefore I suggest you wire them in series. I don't think the tape loop output will work since it is a fixed level signal i. If this isn't possible, you'll have to drill a new hole through the firewall. Since i wont be using any of the factory wiring or amplifier, can you remove the factory amp completely from the vehicle? Might a graphic equalizer be a better idea for me, or would the subwoofer give better bass? This will effectively connect your amplifier and subwoofer together. If each speaker has an impedance below 8 ohms, you should wire them in series. Figure out where you're going to place the amp, put the beginning of your power red wire there and give it about a foot of wire extra, then begin to hide and run the power wire to under the hood.
Connect the subwoofer output to the amplifier input. Then another pair of subwoofer you need to any 2 speaker. Will my thought of connection to existing harness wires affect something negatively? There are many cases when you want to connect four speakers to a stereo amp, that is, to connect 2 speakers to each amplifier — or four speakers in total. My question to sacrifice a box terminals, we are planning on the receiver. Getting signal to the speakers The speakers are usually in four different corners of your vehicle, and running separate new speaker wires to each one presents many challenges, including how to get the wire past the car door hinges to the front door speaker locations.